  Play Video (12,1mb WMV)
Features
- Organic and Non-Toxic
- Odorless
- Environmentally safe
- Safe for use around plants, animals and people
- Works in all climatic conditions
- Non-staining
- Effective against ants
- Reduces weed growth from wind blown germination
- Saves time and Labor
- Activates with water
- Ready for Traffic Immediately
- Will not deteriorate
- Self Healing
- Totally inert
SANDLOCK is a joint sand stabilizer additive for flexible and semi-rigid pavement systems using segmental pavers. When activated with water, SANDLOCK forms a natural, rubberized 'glue', that binds the joint sand. SANDLOCK remains flexible and will accommodate thermal movement. Its ‘self healing’ properties allow SANDLOCK to rebind loosened material with any moisture. SANDLOCK is excellent for concrete, clay brick or natural stone pavements. SANDLOCK prevents sand loss due to wind, traffic, moisture or thermal movement. SANDLOCK does not dilute like water based chemical sealers or break down from ultraviolet light. It will save time and money over chemical joint stabilizers. Compaction and stabilization are both done at once. No harsh chemical cleaners are needed prior to application.
SANDLOCK is available as an Additive and Premix
SANDLOCK Additive
SANDLOCK ADDITIVE can be mixed with joint sand on the job site. Mix approximately 3-4 pounds of SANDLOCK for every 100 pounds of joint sand, sweep into joints with a broom. Continue spreading SANDLOCK Additive with a broom during compaction until joints are full. Sweep off excess SANDLOCK ADDITIVE, followed by a blower to further clean the surface, then activate by gently saturating the surface with water. Then let it set. NO additional steps are required.
SANDLOCK Additive Specifications
2 lb. Tub (2 pack)
Part Number: 002704
Weight: 5 lbs (2.3 kg.)
Case (12 – 2 lb Tubs)
Part Number: 002712
Weight: 29 lbs (13.2 kg.)
Master Pack (2 Cases of 12 – 2 lb Tubs)
Part Number: 002748
Weight: 58 lbs (26.4 kg.)
25 lb. Pail
Part Number: 002707
Weight: 25 lbs (11.4 kg.)
40 lb. Bag
Part Number: 002740
Weight: 40 lbs (18.2 kg.)
SANDLOCK Premix
Once pavers are installed, empty the bags of SANDLOCK PREMIX over the pavement and spread into joints with a broom. Continue spreading SANDLOCK PREMIX with a broom during compaction until the joints are full. Sweep off excess SANDLOCK PREMIX, followed by a blower to further clean the surface, then activate by gently saturating the surface with water. Then let it set. NO additional steps are required.
SANDLOCK Premix Specifications
50 lb. Bags
Minimum order quantity 60 bags
Application WARNING
1. In paver areas where there are periods of prolonged moisture, the use of SANDLOCK is not recommended.
2. Do not use SANDLOCK treated joint sand if you are planning on using a coating type sealer such as acrylics, epoxy, or urethane. The solids in the sealers will be sufficient to bind the joint sand.
3. If applying a coating type sealer to pavers with SANDLOCK stabilized joints in moisture prone areas, there is a risk of mold or mildew in the joints.
DIRECTIONS FOR USE (Complete instructions provided with product)
Directions for use on wide joints (over ½")
INSTALL PAVERS
Install pavers on 1" of bedding sand as recommend by ICPI specifications. It is not necessary to stabilize bedding sand.
SANDLOCK
Use SANDLOCK only for joint sand stabilization. Do not stage or mix SANDLOCK on asphalt. SANDLOCK attracts any moisture and will dry the oils in asphalt.
SWEEP AND COMPACT JOINT SAND
Sweep all SANDLOCK into paver joints. Compact the pavers to insure proper interlock. Remove all excess material from the surface of pavers. Any excess material on the pavers will require pressure washing to remove once activated.
SANDLOCK is activated by gently saturating the pavement with water. Do not use a pressure washer to flood the joints (joint sand may be removed).
| 
